eu reach annex xvii adds new microplastics restriction clauses -伟德国际victor1946

eu reach annex xvii adds new microplastics restriction clauses
published: author: visits: 414

eu,reach,amendments,microplastic,restriction,annex

on september 27, 2023, eu made updates to its reach regulation in its amendments regulation (eu) 2023/2055. this amendment introduced article 78 to annex xvii of the reach regulation (eu no 1907/2006), which pertains to restrictions on synthetic polymer particles (microplastics). additionally, it included rules for degradability certification in appendix 15 and solubility certification in appendix 16.

this regulation will come into effect on october 17, 2023.

background

tiny fragments of synthetic or chemically modified natural polymers are widely present in the environment. they are both insoluble in water and degrade extremely slowly, posing potential risks to the environment and human health. these polymers gradually accumulate in the environment, leading to an increasingly severe plastic pollution problem.

to address plastic pollution, the european commission released a plastic strategy in january 2018, aimed at reducing all sources that could lead to microplastic pollution. with the subsequent releases of the european green deal in december 2019, the new circular economy action plan in march 2020, and the zero pollution action plan in may 2021, this objective was emphasized again, especially in the zero pollution action plan, where the commission set a goal to reduce plastic microfiber pollution by 30% by 2030.

scope of regulation

these restriction clauses primarily target intentionally added microplastics, while unintentionally generated microplastics, such as those resulting from the breakdown of large plastic waste, tire and road paint wear, or the washing of synthetic fiber clothing, are not subject to control. all synthetic polymer particles that are equal to or less than 5mm in size, insoluble in water, and non-degradable are included in the regulation.

restriction conditions

the following items have been added to the reach annex xvii restricted substances list:

[include specific items as needed]

78. synthetic polymer microparticles:

polymers that are solid and which fulfil both of the following conditions:

(a)  are contained in particles and constitute at least 1 % by weight of those particles; or build a continuous surface coating on particles;

(b) at least 1 % by weight of the particles referred to in point (a) fulfil either of the following conditions:

(i) all dimensions of the particles are equal to or less than 5 mm;

(ii) the length of the particles is equal to or less than 15 mm and their length to diameter ratio is greater than 3.

the following polymers are excluded from this designation:

(a) polymers that are the result of a polymerisation process that has taken place in nature, independently of the process through which they have been extracted, which are not chemically modified substances;

(b) polymers that are degradable as proved in accordance with appendix 15;

(c) polymers that have a solubility greater than 2 g/l as proved in accordance with appendix 16;

(d) polymers that do not contain carbon atoms in their chemical structure.

 

1. shall not be placed on the market as substances on their own or, where the synthetic polymer microparticles are present to confer a sought-after characteristic, in mixtures in a concentration equal to or greater than 0,01 % by weight.

2. for the purposes of this entry, the following definitions apply:

(a) “particle” means a minute piece of matter, other than single molecules, with defined physical boundaries;

(b) “solid” means a substance or mixture other than a liquid or gas;

(c)  “gas” means a substance or mixture which at 50 °c has a vapour pressure greater than 300 kpa (absolute), or is completely gaseous at 20 °c at a standard pressure of 101,3 kpa;

(d) “liquid” means a substance or mixture that meets any of the following conditions:

(i) the substance or mixture at 50 °c has a vapour pressure of not more than 300 kpa, is not completely gaseous at 20 °c and at a standard pressure of 101,3 kpa, and has a melting point or initial melting point of 20 °c or less at a standard pressure of 101,3 kpa;

(ii) the substance or mixture fulfils the criteria in the american society for testing and materials (astm) d 4359-90 standard test method for determining whether a material is a liquid or a solid;

(iii) the substance or mixture passes the fluidity test (penetrometer test) described in chapter 2.3.4 of part 2 of annex a to the european agreement concerning the international carriage of dangerous goods by road (adr) concluded at geneva on 30 september 1957;

(e) “make-up product” means any substance or mixture intended to be placed in contact with specific external parts of the human body, namely the epidermis, eye brows and eye lashes, with a view to, exclusively or mainly, changing their appearance;

3. where the concentration of synthetic polymer microparticles covered by this entry cannot be determined by available analytical methods or accompanying documentation, in order to verify the compliance with the concentration limit referred to in paragraph 1, only the particles of at least the following size shall be taken into account:

(a) 0,1 μm for any dimension, for particles where all dimensions are equal to or smaller than 5 mm;

(b) 0,3 μm in length, for particles that have a length that is equal to or smaller than 15 mm and a length to diameter ratio greater than 3.

4. paragraph 1 shall not apply to the placing on the market of:

(a) synthetic polymer microparticles, as substances on their own or in mixtures, for use at industrial sites;

(b) medicinal products within the scope of directive 2001/83/ec and veterinary medicinal products within the scope of regulation (eu) 2019/6 of the european parliament and of the council;

(c)  eu fertilising products within the scope of regulation (eu) 2019/1009 of the european parliament and of the council;

(d) food additives within the scope of regulation (ec) no 1333/2008 of the european parliament and of the council;

(e) in vitro diagnostic devices, including devices within the scope of regulation (eu) 2017/746 of the european parliament and of the council;

(f)  food within the meaning of article 2 of regulation (ec) no 178/2002, not covered by point (d) of this paragraph, and feed as defined in article 3(4) of that regulation.

5. paragraph 1 shall not apply to the placing on the market of the following synthetic polymer microparticles, as substances on their own or in mixtures:

(a) synthetic polymer microparticles which are contained by technical means so that releases to the environment are prevented when used in accordance with the instructions for use during the intended end use;

(b) synthetic polymer microparticles the physical properties of which are permanently modified during intended end use in such a way that the polymer no longer falls within the scope of this entry;

(c) synthetic polymer microparticles which are permanently incorporated into a solid matrix during intended end use.

6. paragraph 1 shall apply as follows regarding the following uses:

(a) from 17 october 2029 to synthetic polymer microparticles for use in the encapsulation of fragrances;

(b) from 17 october 2027 for “rinse-off products” as defined in point (1)(a) of the preamble to annexes ii to vi to regulation (ec) no 1223/2009 unless such products are covered by point (a) of this paragraph or contain synthetic polymer microparticles for use as an abrasive, i.e. namely to exfoliate, polish or clean (“microbeads”);

(c) from 17 october 2035 for lip products as defined in point (1)(e) of the preamble to annexes ii to vi to regulation (ec) no 1223/2009, nail products as defined in point (1)(g) of the preamble to annexes ii to vi to that regulation, and make-up products within the scope of that regulation, unless such products are covered by points (a) or (b) of this paragraph or contain microbeads;

(d) from 17 october 2029 for leave-on products, as defined in point (1)(b) of the preamble to annexes ii to vi to regulation (ec) no 1223/2009, unless such products are covered by points (a) or (c) of this paragraph;

(e) from 17 october 2028 for detergents, as defined in article 2(1) of regulation (ec) no 648/2004, waxes, polishes and air care products, unless those products are covered by point (a) of this paragraph or contain microbeads;

(f) from 17 october 2029 for “devices”, within the scope of regulation (eu) 2017/745 of the european parliament and of the council, unless those devices contain microbeads;

(g) from 17 october 2028 for “fertilising products”, as defined in article 2, point (1), of regulation (eu) 2019/1009, which do not fall within the scope of that regulation;

(h) from 17 october 2031 for plant protection products within the meaning of article 2(1) of regulation (ec) no 1107/2009 of the european parliament and of the council and seeds treated with those products, and biocidal products as defined in article 3(1), point (a), of regulation (eu) no 528/2012 of the european parliament and of the council;

(i) from 17 october 2028 for products for agricultural and horticultural uses not covered by points (g) or (h);

(j) from 17 october 2031 for granular infill for use on synthetic sports surfaces.

7.  from 17 october 2025 suppliers of synthetic polymer microparticles referred to in paragraph 4, point (a), shall provide the following information:

(a) instructions for use and disposal explaining to industrial downstream users how to prevent releases of synthetic polymer microparticles to the environment;

(b) the following statement: “the synthetic polymer microparticles supplied is subject to conditions laid down by entry 78 of annex xvii to regulation (ec) no 1907/2006 of the european parliament and of the council”;

(c) the information on quantity or, as applicable, concentration of synthetic polymer microparticles in the substance or mixture;

(d) generic information on the identity of the polymers contained in the substance or mixture that enables manufacturers, industrial downstream users and other suppliers to comply with their obligations laid down in paragraphs 11 and 12.

8. from 17 october 2026 suppliers of products containing synthetic polymer microparticles referred to in paragraph 4, point (e), and from 17 october 2025 suppliers of products containing synthetic polymer microparticles referred to in paragraph 4, point (d), and paragraph 5, shall provide instructions for use and disposal explaining to professional users and the general public how to prevent releases of synthetic polymer microparticles to the environment.

9. from 17 october 2031 until 16 october 2035 suppliers of products referred to in paragraph 6, point (c), containing synthetic polymer microparticles shall provide the following statement: “this product contains microplastics.” however, products placed on the market before 17 october 2031 are not required to bear that statement until 17 december 2031.

10. the information referred to in paragraphs 7, 8 and 9 shall be provided in the form of clearly visible, legible and indelible text or, where appropriate regarding the information in paragraphs 7 and 8, in the form of pictograms. the text or pictograms shall be placed on the label, the packaging, or the package leaflet of the products containing synthetic polymer microparticles or, regarding the information in paragraph 7, on the safety data sheet. in addition to the text or pictograms, suppliers may provide a digital tool that gives access to an electronic version of that information.

where instructions for use and disposal are provided in accordance with paragraphs 7, 8 and 9 in the form of a text, they shall be in the official languages of the member states where the substance or mixture is placed on the market, unless the member states concerned provide otherwise.

11. starting from 2026 manufacturers and industrial downstream users of synthetic polymer microparticles in the form of pellets, flakes, and powders used as feedstock in plastic manufacturing at industrial sites, and, starting from 2027, other manufacturers of synthetic polymer microparticles and other industrial downstream users using synthetic polymer microparticles at industrial sites shall submit the following information to the agency by 31 may of each year:

(a) a description of the uses of synthetic polymer microparticles in the previous calendar year;

(b) for each use of synthetic polymer microparticles, generic information on the identity of the polymers used;

(c) for each use of synthetic polymer microparticles, an estimate of the quantity of synthetic polymer microparticles released to the environment in the previous calendar year, which shall include also the quantity of synthetic polymer microparticles released to the environment during transportation.

(d) for each use of synthetic polymer microparticles, a reference to the derogation laid down in paragraph 4, point (a).

12. from 2027, suppliers of products containing synthetic polymer microparticles referred to in paragraphs 4, points (b), (d) and (e), and paragraph 5, placed on the market for the first time to professional users and the general public, shall submit the following information to the agency by 31 may of each year:

(a) a description of the end uses for which the synthetic polymer microparticles were placed on the market in the previous calendar year;

(b) for each end use for which the synthetic polymer microparticles were placed on the market, generic information on the identity of the polymers placed on the market in the previous calendar year;

(c) for each end use for which the synthetic polymer microparticles were placed on the market, an estimate of the quantity of synthetic polymer microparticles released to the environment in the previous calendar year, which shall include also the quantity of synthetic polymer microparticles released to the environment during transportation.

(d) for each use of synthetic polymer microparticles, a reference to the applicable derogation or derogations laid down in paragraph 4, point (b), (d) or (e), or 5 point (a), (b) or (c).

13. the agency shall make the information submitted under paragraphs 11 and 12 available to the member states.

14. manufacturers, importers and industrial downstream users of products containing synthetic polymer microparticles shall provide specific information on the identity of polymers covered by this entry contained in those products and the function of those polymers in the products to competent authorities upon their request. the specific information on the polymer identity shall be sufficient to unequivocally identify polymers and shall at least include the information laid down in points 2.1 to 2.2.3 and points 2.3.5, 2.3.6 and 2.3.7 of annex vi, where applicable.

if the information is not available to industrial downstream users, they shall request it from their supplier within 7 days from the receipt of the request from the competent authorities and shall inform the authorities of the request made without delay.

having received the request referred to in the second subparagraph, the suppliers shall provide the requested information within 30 days to the industrial downstream user or directly to the competent authority requesting it.

where the supplier provides the information to the industrial downstream user, the industrial downstream user shall forward that information to the competent authorities without delay.

where the supplier provides the information directly to the authority, it shall without delay inform the industrial downstream user concerned to that effect.

15. manufacturers, importers and industrial downstream users of products containing polymers claimed to be excluded from the designation of synthetic polymer microparticles on grounds of degradability or solubility shall provide, without delay, information proving that those polymers are degradable in accordance with appendix 15 or soluble in accordance with appendix 16, as applicable, to competent authorities upon their request.

16. paragraph 1 shall not apply to placing on the market of synthetic polymers microparticles, on their own or in mixtures, placed on the market before 17 october 2023.

however, the first subparagraph shall not apply to the placing on the market of synthetic polymers microparticles for uses listed in paragraph 6.

warm reminder

the industries most impacted by these restriction clauses are mainly synthetic sports field surface filling materials, cosmetics, cleaning products, some fertilizers, plant protection products, etc. relevant manufacturers should prepare for formulation adjustments and upgrades. products used in industrial settings or products that do not release microplastics during use are not subject to sales restrictions. however, manufacturers must provide instructions on how to use and handle the products to prevent the release of microplastics.

if you need any assistance or have any questions, please get in touch with us via .

网站地图